【Instructions】:
[1] Power on: red light, blue light and green light each flash once and then go out
[2] Standby: the red light flashes in the state of breathing, and the temperature reaches the highest temperature, and it will automatically turn to the blue light in the mid-range. It will automatically shut down after 2 hours.
[3] Working status: indicator light is always on (high-end: red light is always on, mid-range: blue light is always on, low-end, green light is always on)
[4] Long press the power button for 3 seconds: enter the standby state or shut down
[5] Click the switch key: switch gears
[How to use the switch]: Long press for 3 seconds to turn on, the red breathing light will turn on when it reaches a certain temperature, it will automatically turn blue, lightly press to change to blue light, the temperature is medium temperature, lightly press twice to change to green, the temperature is Lowest, press three times for the red three-level high temperature, long press for 3 seconds to shut down, standby for 2 hours automatically shut down, no longer have to worry about wasted power consumption
【Installation Notes】:
[1] First remove the original handlebar with a tool, and then clean the handlebar
[2] Then moisten the inner holes of the left and right handles of the product with soapy water, respectively, install the left and right handles on the handlebars, and the twisting amplitude should not be too large during installation.
[3] When installing the right handlebar, the power cord should be left enough for rotation to facilitate the rotation of the accelerator
[4] Then fix the S bracket on the handle of this product to the position where the handle has screws, and then fix the wire on the bracket to avoid the handle wire from shaking back and forth to reduce damage
[5] Then connect the red wire of the product power cord to the positive pole of the power supply of the car, and connect the black wire of the product power supply to the negative pole of the power supply of the car.
[6] Because the switch of this product has two fixing methods (rearview mirror fixing and 3M glue fixing), you can fix the aluminum alloy switch to the L bracket with small screws, and then fix the L bracket to the rearview mirror base and tighten; Or directly use 3m film to stick to the back of the aluminum alloy switch, and then stick the 3m glue to a suitable position on the car to fix it.

【Precautions】:
[1] When installing the left handle, do not twist the handle too much. Excessive twisting will cause the heating wire to shift
[2] For models with balance iron, please adjust the installation position of the balance iron. Do not squeeze the handle when tightening the screws. The balance iron is slightly separated from the handle. If the installation position of the balance iron cannot be adjusted, please add a spacer between the balance iron and the handle. Excessive squeezing of the handle will cause difficulty in turning the handle switch and abnormal damage such as the heating wire squeezing out of the handle surface.
[3] The above installation steps are only suitable for general models, and the specific installation steps for special models please install according to your own model
【Product advantages】:
【1】The product adopts one-piece molding design to prevent rain and dust from entering the internal corrosion parts, and the service life is longer and safer
[2] The product switch has a built-in intelligent temperature control chip, three levels of temperature adjustment, you can adjust the temperature at will according to your needs, and the intelligent temperature control is safer
[3] The product is 12V voltage, 22MM handlebar common inner diameter, suitable for most motorcycles
[4] The product design adopts the double-throttle line buckle design, and the installation range is wider
[5] The handle of the product adopts a sealable and portable design, which does not affect the installation of decorative accessories such as handle block outside the handle, which is more beautiful and convenient to use
[6] The product has added a standby mode. After switching to the standby state, the electric heating handle will automatically maintain a constant temperature of about 50 degrees, and it will automatically shut down after two hours, so there is no need to worry about losing power to the motorcycle due to forgetting to turn off the switch.
[7] The product line is equipped with a 7.5A fuse and a waterproof cover, which can automatically cut off the power when the car has a problem, effectively preventing the occurrence of dangerous accidents

[Product wiring method]:
1. Connect to the motorcycle electric door lock (behind the key), the red wire to the positive output wire of the electric door lock, and the black wire to any negative electrode or grounding on the car [This method is suitable for use, but it is easy to forget that you don't want to use the standby state Drivers with the switch off]
2. Connect to the positive and negative positions of the battery, connect the red to the positive electrode of the battery [+], and connect the black wire to the negative electrode of the battery [-] Because this electric heating handle adds the function of automatic shutdown in standby, even if you forget to turn off the switch after receiving the battery, just turn it on When in standby mode, you don't have to worry about running out of battery (it is recommended to turn on in advance in standby mode)

Reminder:When wiring, connect the red to the positive pole and the black to the negative pole. If the switch is connected reversely, the switch will burn, but the handle will heat up, so when wiring, please make sure the positive and negative terminals are connected before wiring to prevent burning.