FTDI UMFT4222EV Development Module
FTDI UMFT4222EV Development Module supports prototyping and development of the FT4222H High-Speed USB2.0 to QuadSPI/I?C Bridge ICs. Designed as a small PCB, UMFT4222EV plugs into a standard 0.8″ wide 24-pin DIP socket. Key UMFT4222EV features include: a single high-speed USB 2.0 chip (FT4222H) for flexible and configurable SPI/I?C interfaces; up to 28Mbps data transfer rate in SPI mode with quad data mode; support for up to 4 slave selection control pins in SPI master mode; support for single SPI Slave Mode with SCK operating frequency up to 20MHz; OTP memory for vendor-specific information; on-board jumper for FT4222H configuration mode: USB power configuration and VCCIO source selection; true 3.3V CMOS drive output and TTL input; FTDI’s royalty-free Direct (D2XX) drivers; and on-board USB Micro-B receptacle.

Features
Single Hi-Speed USB 2.0 chip (FT4222H) to flexible and configurable SPI/I?C interfaces.
SPI interface support for Single / Dual / Quad SPI Master Mode with configurable target operating speed.
Up to 28Mbps data transfer rate in SPI mode with quad data mode.
Support up to 4 slave selection control pins in SPI master mode.
Support Single SPI Slave Mode with SCK operating frequency up to 20MHz.
I?C interface support 7-bits address and fully compatible to v2.1 and v3 specification for I2C Master/Slave Mode with configurable target operating speed for 100kbit/S standard mode, 400kbit/S fast mode 1Mbit/S Fast mode plus and 3.4Mbit/S high speed mode.
Configurable GPIOs controlled by application software via USB bus
Fully support USB2.0 suspend/resume and remote wakeup
Support Battery Charger Detection
OTP memory inside for USB Vendor ID (VID), Product ID (PID), device serial number, product description string and various other vendor specific data.
USB Power Configurations; bus-powered and self-powered.
On board jumper for FT4222H configuration mode, USB power configuration and VCCIO source selection
Integrated power-on-reset circuit.
True 3.3V CMOS drive output and TTL input. (operates down to 1.8V with external 1.8V power input to VCCIO)
Support wide supply voltage range.
USB2.0 Low operating and suspend current; 68mA (active-typ.) and 375uA (suspend-typ.).
Configurable I/O pin output drive strength: 4mA (min) and 16mA (max)
UHCI / OHCI / EHCI / XHCI host controller compatible
FTDI’s royalty-free Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases
Supplied PCB designed to fit a standard 20.2mm (0.8″) wide 24 pin DIP socket. Pins are on a 2.54mm (0.1″) pitch.
On board USB Micro-B receptacle allows module to be connected to a PC.
Applications
USB to single mode SPI master controller
USB to dual mode SPI master controller
USB to quad mode SPI master controller
USB to single SPI slave controller
USB to I?C master interface controller
USB to I?C slave interface controller
Utilizing USB to add system modularity
Incorporate USB interface to enable PC transfers for development system communication
USB Industrial Control
USB Data Acquisition
Accessory connectivity solutions for mobiles and tablets
USB dongle implementations for Software/Hardware Encryption and Wireless Modules
Detect USB dedicated charging ports, to allow for high current battery charging in portable devices

Driver Support
Royalty free D2XX Direct Drivers (USB Drivers + DLL S/W Interface)
Windows 8.1: 32, 64-bit
Windows 8: 32, 64-bit
Windows 7: 32, 64-bit
Win XP, Server 2003 and Server 2008